[PDF] Top 20 Phase Modulated Mode-Locked Figure Eight Fiber Laser

... 3 Phase Modulated Mode-Locked Figure Eight Fiber Laser As mentioned in Chapter 2, we purpose design another active mode-locked fiber ... See full document

... Various Mode-Locked Laser with dispersion compensated fiber Through the completed theoretical and experimental analysis of amplitude and phase modulated mode-locked ... See full document

... 2.1. Laser configuration The experimental setup for the ARHM fiber laser is illustrated in figure ...hybrid mode-locked Er-fiber laser configuration, in which the ... See full document

... of phase-tuning, and with narrow bandwidth or frequency-dependent oper- ...optoelectronic phase-shifters (OEPSs) have been demonstrated by using different techniques like a set of optical fibers with different ... See full document

... the fiber laser comb. The repetition fre- quency was phase-locked to SYN1 by controlling the ...was phase-locked to SYN3 by controlling the current of the pump laser ... See full document

... − 3 dBm remains below the FEC criterion of 3.8 × 10 −3 , the BER performance can still be slightly improved with enlarged injection level, as the threshold current and the RIN of DMLD can be suppressed to mitigate the ... See full document

... GHz mode-locked laser is measured. Figure 5 shows the measured RIN at dif- ferent pump ...the laser noise per- formance can be further improved by enhancing the noise sup- pression ... See full document

... SETUP Figure 1 illustrates the backward-optical-injection mode-locked SOAFL system with a ring cavity length of 14 m, which consists of one traveling-wave typed SOA at 1530 nm, an optical circulator, ... See full document

... pulse laser source has attracted a lot of attention all over the ...active mode-locked laser is the most efficient method to generate high data rate and ultrashort ... See full document

... and modelocked operation of Ybdoped fiber lasers is investigated by employing an acoustooptic modulator (AOM) in a linear cavity ...harmonic modelocked pulses with near 100% ... See full document

... 1820 IEEE PHOTONICS TECHNOLOGY LETTERS, VOL. 16, NO. 8, AUGUST 2004 Fig. 2. Optical spectra of mutually injection-locked EDFA-FPLD link with different feedback injecting power (a) 0.37, (b) 4.5, and (c) 5.4 mW. ... See full document

... pulse mode-locked lasers are theoretically investigated by the linearized backpropagation method for the first ...the mode- locked laser noises without the need of assuming a particular ... See full document

... SSB phase noise (or timing jitter) reduction ...SSB phase noise characteristic of a SOA- filtered EDFL has never been ...SSB phase noise reduction of a mode-locked EDFL by changing the ... See full document

... In order to achieve the maximum possible dynamic range of the sensor output, the bias point of the ring resonator can be stabilized such that the spectral lines are located at[r] ... See full document

... Ti:sapphire laser pulses propagate through the tapered ...dimensional mode field distribution for 800 nm ...the mode field is estimated to be about ... See full document

... harmonic mode-locking of an Er- bium-doped fiber ring laser (EDFL) at repetition frequency of 40 GHz is demonstrated by using a purely loss-modulated Fabry–Pérot laser diode (FPLD) at 1 ... See full document

... erbium-doped fiber, a wavelength division multiplexing (WDM) fiber coupler was connected for providing 980 nm of pump power, which was provided by an argon-laser pumped Ti : sapphire ...cleaved ... See full document

... the phase noise of the EDFL-SOA link as the SOA operates at under transparent gain condition, whereas the SSB phase noise is mainly contributed by the stimulated emission of the SOA operated at over ... See full document

... amplifier, fiber ring laser, optically injection mode-locked, harmonically mode-locked, single-mode FPLD, self-seeding ...Pulsed fiber optical sources with ... See full document

... The used nonlinear MF (PM 760, crystal fiber inc.) has the core diameter about 1.7µm and the pitch Λ (spacing between adjacent holes) about 1.4µm. The fiber has two zero dispersion points at 760 nm and 1160 ... See full document