9.4 Joint Channel Estimation and Data Detection
9.4.3 Simulation Study
We illustrate the performance of the proposed SFT MIMO OFDM and compare it with that of the conventional MIMO OFDM [17] and the MIMO CP BSC [17, 90], all with FEC coding, by way of simulation. In fact, the MIMO CPBSC can be considered a particular kind of SFT MIMO OFDM. For the SFT, we use FFT for the orthogonal transform.
The profile of the simulated system is the same as described one in above simulations. In addition, a frame contains 5 bursts, with each burst made of 5 MIMO OFDM symbols following 1 short pilot symbol. The FFT size of the pilot symbol is 256 only. Therefore, the pilot-data ratio is 1/20 in terms of bandwidth consumption. The pilot symbol contains BPSK-modulated sequences that are mapped to the subcarriers of each antenna in an interleaved manner [4].
In the receiver, the adaptive channel predictor has five predictor taps. The maximum number of iterations of the joint CE-DD is 10 and the iteration may stop early if the decoder output contains no error. Shaping filtering is used in the earlier iterations of the TDFE and the switching from shaped to unshaped operation depends upon the convergence of the output log-likelihood ratio (LLR) of the FEC decoder.
Consider a 2×2 MIMO block time-varying channel with the same profile in section 9.3.2. Let the carrier frequency be 2.5 GHz and the channel bandwidth be 10 MHz. Consider three mobile speeds: 50, 100, and 200 km/h, which correspond roughly to maximum normalized Doppler shifts of 0.0125, 0.025, and 0.05, respectively.
Figs. 9.8 and 9.9 illustrate the block error rate (BLER) and the bit error rate (BER) perfor-mance of the three transmission schemes, where a block means the period of one OFDM symbol.
At the two slower mobile speeds, the channel estimation mechanism proposed in this work can track the channel variation well. Its tracking ability is reduced at the highest mobile speed, as indicated by the error floors in the plots. In all cases, the SFT MIMO OFDM performs better than the conventional MIMO OFDM and the MIMO CPBSC. The performance gain is roughly 4 dB over conventional MIMO OFDM and 2 dB over MIMO CPBSC at the lower mobile speeds.
The error floor happens when mobile velocity is 400 Km/Hr, since the prediction error floor introduces large error of the initial channel estimation and the outage occurs frequently in high
4 6 8 10 12 14 16 18 20 22
Figure 9.8: Block (symbol) error rates of different transmission schemes over block time-varying channel.
velocity, which yields poor tracking ability for the receiver. To eliminate this floor, one way is to insert pilot symbol frequently; however, this reduce the bandwidth efficiency. Another way may consider temporal domain interpolative channel estimation instead of the channel forecasting;
which can be treated as a extrapolation and yields more error due to AWGN. Besides, the more accurate estimation of the delay subspace will provide larger noise reduction factor and give more clear channel estimation results to avoid the floor due to estimation error.
9.5 Conclusions
In this part, we showed the optimal design criteria of the coded MIMO OFDM transmission and proposed the design of the MIMO OFDM system, which involves the space-frequency transform, the frame structure and the receiver design. We suggested the SFT design to achieve the optimal design criteria, which is a two-step transform. The first step performs the orthogonal transform to spread the coded symbols and the second step interleaves the spread samples over frequent and spatial dimensions. For the frame design, we presented a simple pilot-data separated design to improve the spectrum efficiency by eliminating the pilot utilities. The receiver employs the IS process to jointly estimate the channel and detect the data. The prior channel references are required in the IS process. Thus, the LSCE from the pilot symbol and the channel prediction scheme are used to obtain these references. Simulations shown that the proposed SFT is superior to the conventional MIMO OFDM and the MIMO SC with CP in terms of the BER and the BLER.
For future researches, it is interest in the design to support multiuser based on the proposed SFT MIMO OFDM system. It could be a CDMA-like or a OFDMA-like schemes in either the uplink or the downlink, which depends on the position of the SFT in the transmission structure. Besides, another design issue is the receiver structure of the multiple access system.
The performance, the complexity and the spectrum efficiency all are the design constrains in
4 6 8 10 12 14 16 18 20 22
Figure 9.9: Bit error rates of different transmission schemes over block time-varying channel.
the realization.
Appendix
Derivation of the MMSE Shaping Filter
First, let the singular value decomposition (SVD) of the channel matrix be given by
H = U ΛV. (9.37)
Since the desired C commutes with H, we may let C = VHΛcV . As in typical adaptive filter analysis, assume that ek−1 is white and uncorrelated with n. Then
J , E{kwkk2}
where λ(k) and λc(k) are the kth singular values of H and C, respectively.
Now, constraining the average of the diagonal elements of B to zero amounts to requiring tr©
Employing the Language multiplier method, we consider the modified cost function
Jm , J + µ Ã
1 − 1 KN
KNX
k=1
λc(k) |λ(k)|2
!
(9.41)
and set ∂Jm/∂λc(k) = 0, which leads to the solution λ∗c(k) = µ
|λ(k)|2+ α (9.42)
and
C∗= µ¡
HHH + αI¢−1
. (9.43)
Substituting C∗ into the constraint on B, we obtain
µ = KN
tr {(HHH + αI)−1HHH}. (9.44)
Chapter 10
Thesis Conclusions and Future Topics
Several algorithms are proposed for the design of the communication receivers in SC QAM, OFDM, and MIMO-OFDM systems. A communication receiver contains two major processing modules. The synchronization calibrates the mismatches between the transmitter and the re-ceiver, and estimates the unknown parameters. The channel distortion compensator is used to remove the channel effects. It can be divided into two parts: the equalization and the channel estimation. In SC QAM systems, we consider the issues in the carrier frequency recovery, the channel equalization, and the joint operation. Both the open-loop frequency estimation and closed-loop carrier recovery loop are studied in the carrier recovery problem. The blind adap-tive DFE is used and studied in the channel equalization. In OFDM system, we consider the synchronization issues in the estimation of the carrier frequency offset and the symbol time, and the cell search of the mobile-WiMAX system. The issue in OFDM channel estimation is studied in the work. We propose two estimation schemes and apply these algorithms in mobile-WiMAX system. In wide-band MIMO system, we study the transform design at the transmitter, propose a space-frequency transform, and use the turbo-DFE as the data detector at the receiver. In summary, the designed algorithms for the corresponding receiver issues are given in Table 10.1.
10.1 Future Research Topics
Some potential research topics are given as follows. First, the adaptive system parameters of the OFDM system can be realized with the knowledge of the channel parameters. Specifically, the CP is used to prevent the IBI effect. If the system has the delay spread of the channel profile, the CP length can be optimized. Besides, the utilization of the pilots also can be optimized if the performance of the channel estimator can be predicted. For example, consider channel estimation with polynomial interpolation in the comb-type OFDM system. If σ2ξ(N, τco) and the noise variance can be estimated in advance, the estimate MSE is a function of the pilot subcarrier spacing F . Thus, the optimization of the pilot subcarrier spacing can optimize the pilot utilization.
Secondly, what is a good interpolator of the channel estimation according to the pilot struc-ture? Specifically, consider the approximate LMMSE CE approach. The pre-defined PDP shape is constructed according the estimated delay spread and the mean delay of the channel, but it may not be the optimal approximation of the PDP event if the same profile model is used. It is interesting to estimate the optimal parameters of the profile model to match the true channel PDP or to optimize the channel estimate MSE. Besides, according to the window shift concept, what is a suitable interpolator for the given pilot assignment and what is the optimal window shift corresponding to the suitable interpolator?
Finally, the relay extension system in MIMO communication currently is a popular research topic. We may apply the transform MIMO-OFDM in such scenarios. The design of the trans-form, the receiving process, and the practical realization are potential topics.
Table 10.1: Proposed algorithms for the corresponding issues
high accuracy and low complexity fre-quency estimator
Reduced-constellation phase detector
SC QAM carrier recovery loop large frequency acquisition range
Hybrid phase detec-tor
SC QAM carrier recovery loop large frequency acquisition range and small steady-state phase noise
Dynamic loop band-width control
SC QAM carrier recovery loop good tracking stability
Boundary mean-square error
SC QAM channel equalization high accuracy MSE estimator at low decision-point SNR
Blind variable step-size algorithm
SC QAM channel equalization fast convergence
Hybrid VSS algo-rithm
SC QAM channel equalization fast convergence and soft switching of op-eration mode
Phase-irrelevant decision feedback equalizer
SC QAM channel equalization convergence of blind DFF in CFO envi-ronment
Frequency domain filtering
OFDM,
WiMAX cell search low complexity estimators in frequency domain
Phase-shift polyno-mial interpolation
OFDM,
WiMAX channel estimation MMSE optimization of the polynomial in-terpolation
Adaptive selection of interpolator
OFDM,
WiMAX channel estimation optimal interpolation-order estimation Mean delay and
RMS delay spread estimator
OFDM,
WiMAX channel estimation low complexity frequency-domain estima-tion
Approximate
LMMSE channel estimator
OFDM,
WiMAX channel estimation low complexity and high performance channel estimator
Space-frequency transform
MIMO-OFDM transmitter design maximal coding and diversity gain Separable
space-frequency interleaver
MIMO-OFDM receiver design separation of de-interleaver outside turbo-DFE loop
MMSE Shaped
turbo-DFE
MIMO-OFDM channel equalizer better convergence property of iterations in turbo-DFE
low pilot utilization and joint estimation of channel and data
Bibliography
[1] S. M. Alamouti, “A simple transmit diversity technique for wireless communications,”
IEEE J. Sel. Area Commun., vol. 16, no. 8, pp. 1451–1458, Nov. 1998.
[2] C. R. N. Athaudage and A. D. S. Jayalath, “Enhanced MMSE channel estimation using timing error statistics for wireless OFDM systems” IEEE Trans. Broadcast., vol. 50, no.
4, pp. 369–376, Dec. 2004.
[3] C. N. R. Athaudage and A. D. S. Jayalath, “Delay-spread estimation using cyclic-prefix in wireless OFDM systems,” IEE Proc.-Commun., vol. 151, no. 6, pp. 559–566, Dec. 2004.
[4] I. Barhumi, G. Leus, and M. Moonen, “Optimal training design for MIMO OFDM systems in mobile wireless channels,” IEEE Trans Signal Process., vol. 51, no. 6, pp. 1615–1624, Jun. 2003.
[5] J.-J. van de Beek, M. Sandell, and P. O. B¨orjesson, “ML estimation of time andfrequency offset in OFDM systems,” IEEE Trans. Signal Processing, vol. 45, pp. 1800–1805, Jul.
1997.
[6] Roland E. Best, Phase-lockeded Loops, McGraw-Hill International, 1997.
[7] E. K. Blum, Numerical Analysis and Computation: Theory and Practice. Reading, Mass.:
Addison-Wesley, 1972.
[8] J. Boutrs and E. Viterbo, “Signal space diversity: power- and bandwidth-efficient diversity technique for the Rayleigh fading channel,” IEEE Trans. Inform. Theory, vol. 44, no. 4, pp. 1453–1467, Jul. 1998.
[9] T. Brown and M. M. Wang, “An iterative algorithm for single-frequency estimation,”
IEEE Trans. Signal Process., vol. 50,no. 11, pp. 2671–2682, Nov. 2002.
[10] K. V. Cartwright, “Blind phase recovery in general QAM communication systems using alternative higher order statistics,” IEEE Signal Processing Lett., vol. 6, no. 12, pp. 327–
329, Dec. 1999.
[11] K. V. Cartwright,“Blind phase recovery in cross QAM communication systems with eighth-order statistics,” IEEE Signal Processing Lett., vol. 8, no. 12, pp. 304–306, Dec. 2001.
[12] F. C. C. De Castro, M. C. F. De Castro, and D. S. Arantes, “Concurrent blind deconvolu-tion for channel equalizadeconvolu-tions,” in Conf. Rec., IEEE Int. Conf. Commun., Jun. 2001, pp.
366–371.
[13] A, M. Chan and G. W. Wornell, “A class of block-iterative equalizers for intersymbol interference channels: Fixed channel results,” IEEE Trans. Commun., vol. 49, no. 11, pp.
1966–1976, Nov. 2001.
[14] C.-C. Chang et al., “A wide pull-in range fast acquistion hardware-sharing two-fold carrier recovery loop,” in Proc. Int. Symp. Circuits Syst., vol. IV, pp. 358–361, May 2001.
[15] P. Ciblat et al., “Performance analysis of blind carrier frequency offset estimators for Non-circular transmissions through frequency-selective channels,” IEEE Trans. Signal Process., vol. 50, no. 1, pp. 130–140, Jan. 2002.
[16] P. Ciblat and M. Ghogho, “Blind NLLS carrier frequency-offset estimation for QAM, PSK, and PAM modulations: performance at low SNR,” IEEE Trans. Commun., vol. 54, no.
10, Oct. 2006.
[17] J. Coon et al., “A comparison study of MIMO-OFDM and MIMO-SCFDE in WLAN environments,” in Proc. GLOBECOM 2003, vol. 6, Dec. 2003, pp. 3296–3301.
[18] O. Edfors, et al. “OFDM channel estimation by singular value decomposition,” IEEE Trans. Commun., vol. 46, no. 4, pp. 931–939, Jul. 1998.
[19] O. Edfors, et al. “Analysis of DFT-based channel estimation for OFDM,” Wireless Per-sonal Commun., vol. 12, no. 1, pp. 55–70, Jan. 1998.
[20] V. Erceg et al., “Channel models for fixed wireless applications,” standards contribution IEEE 802.16.3c-01/29r1, Feb. 23, 2001.
[21] ETSI TR 101 112, “Selection procedures for the choice of radio transmission techNologies of the UMTS,” ETSI Tech. Rep., V3.0.2, pp. 38–43, Apr. 1994.
[22] X. Fang, X. P. Xu and H. Li “A new phase-unwrapping method used in the single frequency estimation,” Proceedings of ICSP, 2004.
[23] M. P. Fitz, “Further results in the fast estimation of a single frequency,” IEEE Trans.
Commun., vol. 42, No. 2/3/4, pp. 862–864, Feb. 1994.
[24] R. Freund, G. Golub, and N. Nachtigal, “Iterative solution of linear systems,” Acta Nu-mer., vol. 1, pp. 57–100, 1992.
[25] H. Fu and P. Y. Kam “MAP/ML estimation of the frequency and phase of a single sinusoid in Noise,” IEEE Trans. Signal Process. vol. 55, no. 3, march 2007.
[26] W. H. Gerstacker, R. R. Muller, and J. B. Huber, “Iterative equalization with adaptive soft feedback,” IEEE Trans. Commun., vol. 48, no. 9, pp. 1462–1466, 2000.
[27] G. H. Golub and C. F. Van Loan Matrix Computations, Johns Hopkins Press Ltd., London, 3rd Edition, 1996.
[28] J. Hagenauer and P. Hoeher, “A Viterbi algorithm with soft-decision outputs and its applications,” in Conf. Rec., IEEE Global Telecommun. Conf., Nov. 1989.
[29] S. Haykin, Adaptive Filter Theory, Prentice-Hall, Inc., New Jersey, 2002.
[30] L. He, M. G. Amin, C. Reed, Jr., and R. C. Malkemes, “A hybrid adaptive blind equal-ization algorithm for QAM signals in wireless communications,” IEEE Trans. Signal Pro-cessing, vol. 45, no. 7, pp. 2058–2069, Jul. 2004.
[31] R. A. Horn and C. R. Johnson, Matrix Analysis. Cambridge, U.K.: Cambridge Univ.
Press, 1999.
[32] M.-H. Hsieh and C.-H. Wei, “Channel estimation for OFDM systems based on comb-type pilot arrangement in frequency selective fading channels,” IEEE Trans. Consumer Electron., vol. 44, no. 1, pp. 217–225, Feb. 1998.
[33] M.-H. Hsieh and C.-H. Wei “A Low-Complexity frame synchronization and frequency offset compensation scheme for OFDM systems over fading channels,” IEEE Trans. Vehicular Tech. vol. 48, no. 5, pp. 1596–1609, Sep. 1999.
[34] K.-C. Hung, D. W. Lin, and C.-N. Ke, “Variable-step-size multimodulus blind decision-feedback equalization for high-order QAM based on boundary MSE estimation,” in Proc.
IEEE int. Conf. Acoust. Speech Signal Process., vol. 4, May 2004, pp. 881–884.
[35] K.-C. Hung and D. W. Lin, “Joint carrier recovery and multimodulus blind decision-feedback equalization under high-order QAM,” in Conf. Rec., IEEE Globe Telecommun.
Conf., Nov.–Dec. 2004.
[36] K.-C. Hung and D. W. Lin, “A Hybrid Variable Step-Size Adaptive Blind Equalization Algorithm for QAM Signals,” in Conf. Rec., IEEE Globe Telecommun. Conf., Nov.–Dec.
2005.
[37] K.-C. Hung and D. W. Lin, “Joint detection of integral carrier frequency offset and pream-ble index in OFDMA WiMAX downlink synchronization,” in in IEEE Wireless Commun.
and Networking Conf. (WCNC), Mar. 2007.
[38] K.-C. Hung and D. W. Lin, “Theory and design of nearoptimal MIMO OFDM transmission system for correlated multipath Rayleigh fading channels,” J. Commun. Networks, vol. 9, no. 2, Jun. 2007.
[39] K.-C. Hung and D. W. Lin, “Joint channel estimation and data detection for space-frequency transformed MIMO OFDM system,” in Taiwan-Japan Joint Conference on Communications Technology, Hsinchu, Taiwan, ROC, pp. 36–40, Nov. 2007.
[40] K.-C. Hung and D. W. Lin, “Jointly iterative channel estimation and data detection for cyclic-prefixed block transmission over time-varying channels,” in International Conference on Information, Communications & Signal Processing, Dec. 2007.
[41] K.-C. Hung and D. W. Lin, “Optimal delay estimation for phase-rotated linear interpola-tive channel estimation in OFDM and OFDMA systems,” IEEE Signal Processing Lett., vol. 15, pp. 349–352, 2008.
[42] K.-C. Hung and D. W. Lin, ”Pilot-aided multicarrier wireless channel estimation via MMSE polynomial interpolation,” in Conf. Rec., IEEE Globe Telecommun. Conf., Nov.–
Dec. 2008.
[43] K.-C. Hung and D. W. Lin, “Pilot-aided multicarrier channel estimation via MMSE linear phase-shifted polynomial interpolation,” submit to IEEE Trans. Wireless Commun.
[44] K.-C. Hung and D. W. Lin, “Pilot-based LMMSE channel estimation for OFDM systems with power-delay profile approximation,” submit to IEEE Trans. Vehicular Tech..
[45] K.-C. Hung and D. W. Lin, “LMMSE channel estimation based on approximated power-delay profile for OFDM systems with distributed pilots,” submit toProc. IEEE int. Conf.
Acoust. Speech Signal Process. 2009.
[46] T. Hwang and Y. Li, “Space-time energy spreading transform based MIMO technique with iterative signal detection,” in Conf. Rec., IEEE Global Telecommun. Conf., Nov. 2004, pp.
2470–2474.
[47] T. Hwang and Y. Li “Novel iterative equalization based on energy-spreading transform,”
IEEE Trans. Signal Processing, vol. 54, no. 1, pp. 190–203, 2006.
[48] IEEE Std 802.16e-2005 and IEEE Std 802.16-2004/Cor1-2005, IEEE Standard for Local and Metropolitan Area Networks — Part 16: Air Interface for Fixed and Mobile Broadband Wireless Access Systems — Amendment 2: Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands. New York: IEEE, Feb. 2006.
[49] C. R. Johnson, Jr. et al., “Blind equalization using the constant modulus criterion: a review,” Proc. IEEE, vol. 86, no. 10, pp. 1927–1950, Oct. 1998.
[50] B. Kaltenbacher, “Some Newton-type methods for the regularization of nonlinear ill-posed problems,” Inverse Problems, vol. 13, no. 3, pp. 729–753, 1997.
[51] S. Kay, “A fast and accurate single frequency estimator,” IEEE Trans. Acoust., Speech, Signal Process., vol. 39, no. 12, pp. 1987–1990, May 1989.
[52] C.-N. Ke, C.-Y. Huang, and C.-P. Fan “An adaptive carrier synchronizer for M-QAM cable receiver,” IEEE Trans. Consum. Elect., vol. 49, no. 4, pp. 983-988,Nov. 2003.
[53] Y. H. Kim, I. Song, S. Yoon, and S. R. Park, “ An efficient frequency offset estimator for OFDM Systems and its performance characteristics,” IEEE Trans. Vehicular Tech., vol.
50, no. 5, pp. 1307–1312, Sep. 2001.
[54] K.-Y. Kim and H.-J. Choi, “Design of carrier recovery algorithm for high-order QAM with large frequency acquisition range,” in Conf. Rec., IEEE Int Conf. Commun., vol. 4, pp.
1016–1020, Jun. 2001.
[55] R. H. Kwong and E. W. Johnson, “A variable step size LMS algorithm,” IEEE Trans.
Signal Processing, vol. 40, no. 7, pp. 1633–1642, Jul. 1992.
[56] C. Laot, A. Glavieux, and J. Labat, “Turbo equalization: adaptive equalization and chan-nel decoding jointly optimized,” IEEE J. Sel. Areas Commun., vol. 19, pp. 1744–1752, Sep. 2001.
[57] E. G. Larsson et al., “Joint symbol timing and channel estimation for OFDM based WLANs” IEEE Commun. Lett., vol. 5, no. 8, pp. 325–327, Aug. 2001.
[58] K. H. Lee, S. C. Jung, and H. J. Choi, “A Novel digital lock detector for QPSK receiver,”
IEEE Commun. Letter, vol. 46, no. 6, pp. 750-753 Jun. 1998.
[59] S. Lee, A. Singer, and N. Shanbhag, “Linear turbo equalization analysis via BER transfer and EXIT charts,” IEEE Trans. Signal Processing, vol. 53, no. 8, pp. 2883–2897, 2005.
[60] Y. Li and K. J. R. Liu, “Static and dynamic convergence behavior of adaptive blind equalizers,” IEEE Trans. Signal Processing, vol. 44, no. 11, pp. 2736–2745, Nov. 1996.
[61] Y. Li, “Pilot-symbol-aided channel estimation for OFDM in wireless systems,” IEEE Trans. Vehic. Tech., vol. 49, no. 4, pp. 1207–1215, Jul. 2000.
[62] A. P. Liavas and D. Tsipouridou “On the performance of the mismatched MMSE and the LS linear equalizers”, IEEE Trans. Signal Process., vol. 55, no. 7, pp. 3302–3311, Jul.
2007.
[63] H. Lim and D. S. Kwon, “Initial synchronization for WiBro,” in Asic-Pacific Conf. Com-mun., 2005, pp. 284–288.
[64] J.-C. Lin, “Maximum-likelihood frame timing instant and frequency offset estimation for OFDM communication over a fast Rayleigh fading channel,” IEEE Trans. Vehic. Tech., vol. 52, no. 4, pp. 1049–1062, Jul. 2003.
[65] L. R. Litwin, M. D. Zoltowski, T. J. Endres, and S. N. Hulyalkar, “Blended CMA: smooth, adaptive transfer from CMA to DD-LMS,” in Proc. IEEE Wireless Commun. Networking Conf., 1999, pp. 797–800.
[66] X. Ma, et al “Non-data-aided carrier offset estimators for OFDM with nullsubcarriers:
identifiability, algorithms, and performance,” IEEE J. Select. Areas Commun., vol. 19, pp. 2504–2515, Dec. 2001.
[67] J. Mai and A. H. Sayed, “A feedback approach to the steady-state performance of frac-tionally spaced blind adaptive equalizers,” IEEE Trans. Signal Processing, vol. 48, no. 1, pp. 80–91, Jan. 2000.
[68] H. Meyr, M. Moeneclaey, and S. A. Fechtel, Digital communication receivers: synchro-nization, channel estimation and signal processing. John Wiley & Sons, inc. New York, 1997.
[69] A. Mileant and S. Hinedi, “On the effect of phase jitter on QPSK lock detection,” IEEE
[69] A. Mileant and S. Hinedi, “On the effect of phase jitter on QPSK lock detection,” IEEE