試數種電阻式及電磁感應加熱組合，最後採用電磁感應的方式加熱磁通金屬 導體，可在 90 秒以內加熱 10*10 cm2區域至 670 ˚C。
6. 玻璃擠出中熔料會因表面能作用出現堆積的現象，使擠條直徑變寬，經由減 少擠出噴頭與加熱基板間距離至 0.50 mm，可避免熔料堆積的現象，並可連 續擠出時間超過 300 s，另一例之平均擠出線速度為 25 mms-1。
7. 量測三種 Cu-85Cu15Ni、Cu-Cu9Ni6Sn 與 Cu-70Cu30Zn 熱電偶於 650 ˚C 以下 之熱電位，最高熱電位分別為 23.93 mV、14.05 mV 以及 1.44 mV，並將熱電 位-溫度圖微分後得席貝克係數，在 650 ˚C 時分別為 60.93 μVK-1、35.1 μ VK-1及 3.252 μVK-1。
8. 利用 TN-SB 5 玻璃鍍膜於三種熱電偶表面，可於 400 ˚C、30 小時之長時間測 試中得到 Cu-85Cu15Ni、Cu-Cu9Ni6Sn 與 Cu-70Cu30Zn 之量測誤差值分別為 0.6%、10.6%與 1.2%，其原因可能為銅晶粒成長，以及接點部分氧化。
參考文獻
[1] I. Campbell, D. Bourell, and I. Gibson, "Additive manufacturing: rapid prototyping comes of age," Rapid Prototyping Journal, 18 [4] 255-58 (2012).
[2] K. V. Wong and A. Hernandez, "A review of additive manufacturing," ISRN Mechanical Engineering, 2012 1-10 (2012).
[3] D. S. Thomas and S. W. Gilbert, "Costs and cost effectiveness of additive manufacturing," NIST Special Publication, 1176 (2014).
[4] Wohlers Associates, "3D printing and additive manufacturing industry expected to quadruple in size in four years", https://wohlersassociates.com/press65.html.
[5] S. R. Scholes, "ASTM :Definition of glass," Glass Ind. , 26 [9] 417, 38 (1945).
[6] J. E. Shelby, Introduction to glass science and technology; pp. 3-5 Royal Society of Chemistry, Cambridge, England, 2005.
[7] G. A. Boyd, G. Tolley, and J. Pang, "Plent level productivity, efficiency, and environmental performance of the container glass," Environmental and Resource Economics, 23 29-43 (2002).
[8] G. H. Beall and D. A. Duke, "Transparent glass-ceramics," J. Materials Science, 4 340-52 (1969).
[9] H. Fatemeh, M. Amir, H. Zohreh, and F. Sajad, "Evaluation on properties of CaO–
BaO–B2O3–Al2O3–SiO2 glass–ceramic sealants for intermediate temperature solid
[12] D. R. Uhlmann, "A kinetic treament of glass formation," J. Non-crystalline solids, 7 337-48 (1972).
[13] Z. P. Lu and C. T. Liu, "Glass formation criterion for various glass-forming systems," Phys Rev Lett, 91 [11] 115505 (2003).
[14] M. Saad and M. Poulain, "Glass forming ability criterion," Materials Science Forum, 19-20 11-18 (1987).
[15] 陳怡如, "BaO-B2O3-SiO2-Al2O3玻璃系統使用在中溫形固態氧化物燃料電池 適宜性之研究", 國立台灣大學碩士論文, 2008.
[16] W. H. Zachariasen, "The atomic arrangement in glass," J. American Chemical Society, 54 [10] 3841-51 (1932).
[17] Y. M. Chiang, D. P. Burnie III, and W. D. Kingery, Physical ceramics: principles for ceramic science and engineering; pp. 80-93 John Wiley & Sons. Inc., 1996.
[18] K. L. Ley, M. Krumpelt, R. Kumar, J. H. Meiser , and I. Bloom, "Glass-ceramic sealants for solid oxide fuel cells part I: Physical properties," J. Materials Research, 11 [6] 1489-93 (1996).
[19] J. E. Shelby, "Thermal expansion of alkali borate glasses," J. Am. Ceram. Soc., 66 [3] 225-27 (1983).
[20] J. H. Strimple, E. A. Giess, "Glass formation and properties of glasses in the system Na2O-B2O3-SiO2-TiO2," J. Am. Ceram. Soc., 41 [7] 231-37 (1958).
[21] D. E. Day and G. E. Rindone, "Properties of Soda Aluminosilicate Glasses I, Refractive Index, Density, Molar Refractivity, and Infrared Absorption Spectra," J. Am.
Ceram. Soc., 45 [10] 489 (1962).
[22] R. C. Turnbull and W. G. Lawrence, "The role of titania in silica glasses," J. Am.
Ceram. Soc., 35 [2] 48-53 (1952).
[23] P. Hrma, "Arrhenius model for high-temperature glass-viscosity with a constant
[24] J. H. Simmons, R. Ochoa, K. D. Simmons, and J. J. Mills, "Non-Newtonian viscous flow in soda-lime-silica glass at forming and annealing temperatures," J. Non-Crystalline Solids, 105 [3] 313-22 (1988).
[25] I. S. O., "Additive manufacturing-general principles," 17296 (2015).
[26] J. P. Kruth, "Material incress manufacturing by rapid prototyping techniques,"
CIRP Annals - Manufacturing Technology, 40 [2] 603-14 (1991).
[27] P. Bertrand, F. Bayle, C. Combe, P. Goeuriot, and I. Smurov, "Ceramic components manufacturing by selective laser sintering," Applied Surface Science, 254 [4] 989-92 (2007).
[28] T. F. McNulty, D. J. Shanefield, S. C. Danforth, and A. Safari, "Dispersion of lead zirconate titanate for fused deposition of ceramics," J. Am. Ceram. Soc., 82 [7] 1757-60 (1999).
[29] A. Bandyopadhyay, R. K. Panda, V. F. Janas, M. K. Agarwala, S. C. Danforth, and A. Safari, "Processing of piezocomposites by fused deposition technique," J. Am.
Ceram. Soc., 80 [6] 1366-72 (1997).
[30] B. R. Munson, D. F. Young, and T. H. Okiishi, Fundamentals of fluid mechanics;
pp. 383-450 Wiley, New york, 1990.
[31] Wikipedia, "Bernoulli's principle",
https://en.wikipedia.org/wiki/Bernoulli%27s_principle.
[32] J. S. Reed, Principles of ceramic processing; pp. 450-473 John Wiley & Sons, Inc.,
walls," J. Am. Ceram. Soc., 85 [8] 2113 (2002).
[36] J. Klein, M. Stern, G. Franchin, M. Kayser, C. Inamura, S. Dave, J. C. Weaver, P.
Houk, P. Colombo, M. Yang, and N. Oxman, "Additive manufacturing of optically transparent glass," 3D Printing and Additive Manufacturing, 2 [3] 92-105 (2015).
[37] G. Olaru, Mold-Master, Ltd.,, "Method and apparatus for measuring the temperature of molten material in a mold cavity", U.S. Pat. 6936199 B2, Jan. 9, 2003.
[38] S. M. SZE, Semiconductor devices physics and technology; pp. 1-21 Gau Lih Book Co. , Taipei, 1996.
[39] 翁上林, 固態物理學概論; pp. 237-296 徐氏基金會, 臺北市, 1979.
[40] A. S. T. M., Manual on the use of thermocouples in temperature measurement; pp.
5-40 ASTM, Philadelphia, 1993.
[41] H. V. Gaskill, Collins Radio Co., "Method of using the peltier effect for cooling equipment", U.S. Pat. 2984077 A, Oct 24, 1958.
[42] J. M. Thomas, Hoskins Mfg Company, "Method and apparatus for prolonging life of thermocouples", U.S. Pat. 2915575 A, Jul 9, 1959.
[43] C. R. Bingham, Honeywell Inc, "Thermocouple comprising intimately twisted wires", U.S. Pat. 3317353 A, dec 6, 1962.
[44] 馮晨光, 葉建明, 安群, 左克勤, 張勛明, 張永隽, 蔣國強, 陳宏橋, 韓 世明, and 高振鷹, 武漢鋼鐵, "Thermocouple butt-welding machine", CN Pat. 202411648 U, Dec 12, 2011.
[45] D. Arthur and M. Clive, Atomic Energy Authority Uk, "Welding thermocouples", U.S. Pat. 3422245 A, Oct 27, 1966.
[46] K. Sumihiko, Koransha Co., Ltd., "Thermocouple protection tube", U.S. Pat.
4060095 A, Aug 17, 1976.
[47] B. H. John, Thermex, Inc., "Insulated thermocouple ", U.S. Pat. 5075514 A, Aug
[48] C. A. Ragsdale, "Thermocouple tube and protective coating", U.S. Pat. 3010480 A, Oct 13, 1958.
[49] J. P. Vollrath, Honeywell Regulator Co, "Thermocouple with wire insulation", U.S.
Pat. 2504764 A, Aug 30, 1946.
[50] J. P. Abulencia and L. Theodore, Fluid flow for the practicing chemical engineer;
pp. 147-166 John Wiley & Sons. Inc., Hoboken, N.J., 2010.
[51] 王郁茹, "銀電極與玻璃陶瓷之介面反應," 國立台灣大學碩士論文, (1995).
[52] M. Adithan and V. C. Venkatesh, "Production accuracy of holes in ultrasonic drilling," Wear, 40 [3] 309-18 (1976).
[53] A.S.T.M. International, "Standard test method for softening point of glass." in Glass; Ceramic Whitewares, Vol. C338-93. 2013.
[54] F. Porte, R. Brydson, B. Rand, and F. L. Riley, "Creep viscosity of vitreous china,"
J. Am. Ceram. Soc., 87 [5] 923-28 (2004).
[55] M. A. Bouhifd, A. Sipp, and P. Richet, "Heat capacity, viscosity, and configurational entropy of alkali titanosilicate melts," Geochimica et Cosmochimica Acta, 63 [16] 2429-37 (1999).
[56] G. S. Fulcher, "Analysis of recent measurements of the viscosity of glasses " J. Am.
Ceram. Soc., 75 [5] 1043-55 (1992).
[57] 陳伍佑, "雷射金屬加工溫度預測暨紅外線溫度量測影響參數探討," 國立
on physical properties of Te9Se72Ge19-xSbx (X = 8, 9, 10, 11, 12) glassy material," New Journal of Glass and Ceramics, 03 [03] 91-98 (2013).
[61] B. E. Warren, "X-Ray determination of the structure of liquids and glass," J.
Applied Physics, 8 [10] 645 (1937).
[62] Y. Yu, D. Chen, Y. Wang, P. Huang, F. Weng, and M. Niu, "Enhanced photoluminescence of Eu3+ induced by energy transfer from In2O3 nano-crystals embedded in glassy matrix," Phys. Chem. Chem. Phys., 11 [39] 8774-8 (2009).
[63] M. L. Huggins, "The density of silicate glasses as a function of composition," J.
the Optical Society of America, 30 [9] 420-30 (1940).
[64] M. K. Mahapatra and K. Lu, "Seal glass for solid oxide fuel cells," Journal of Power Sources, 195 [21] 7129-39 (2010).
[65] G. Gruener, P. Odier, D. De S. Meneses, P. Florian, and P. Richet, "Bulk and local dynamics in glass-forming liquids: A viscosity, electrical conductivity, and NMR study of aluminosilicate melts," Physical Review B, 64 [2] (2001).
[66] B. Dutta and D. E. Day, "Electronic and ionic conduction in sodium borosilicate glasses," J. non-crystalline solids, 48 345-57 (1982).
[67] R. H. Doremus, "Viscosity of silica," J. Applied Physics, 92 [12] 7619 (2002).
[68] P. Richet, M. Roskosz, and J. Roux, "Glass formation in silicates: Insights from composition," Chemical Geology, 225 [3-4] 388-401 (2006).
[69] K. Pelissier, T. Chartier, and J. M. Laurent, "Silicon carbide heating elements,"
Ceramics International, 24 [5] 371-77 (1997).
[70] 陳牧民, "使用生質燃料的固態燃料電池組之開發與測試," 國立台灣大學 碩士論文, (2014).
[71] 周志勳, "銅基材料於固態燃料電池之應用與熱熔擠組件開發," 國立台灣 大學碩士論文, (2015).
Al2O3," J. Am. Ceram. Soc., 55 [5] 249-53 (1972).
[73] Wikipedia, "Moody chart", https://en.wikipedia.org/wiki/Moody_chart.
[74] J. T. Jensen, J. Klebanoff, and G. A. Haas, "Thermocouple errors using Pt-Pt(Rh) thermocouples on Ni surfaces," Review of Scientific Instruments, 35 [12] 1717 (1964).
[75] 王魁漢, 吳玉鋒, 侯素蘭, and 羅濤, "熱電偶的裂化及對策," 工業計量, 6 (2005).