This module is a spring clamp terminal block type and an output module that has indicators for checking the insertion state of wire
4 COMBINED I/O MODULE
4. COMBINED I/O MODULE
4.1 QH42P I/O Module
• When using the main module, use the constructions listed in Section 1.2.3 (2).
• This module uses same I/O numbers for input and output.
For I/O numbers of combined I/O modules, refer to Section 1.2.3.
(1) DC Input Specification (Positive Common Type)
Type
Specifications QH42P I/O Module (Input Specification)
Number of input points 32 points
Insulation method Photocoupler
Rated input voltage 24VDC (+20/-15%, ripple ratio within 5%)
Rated input current Approx. 4mA
Input derating See the derating chart.
ON voltage/ON current 19V or higher/3mA or higher OFF voltage/OFF current 11V or lower/1.7mA or lower
Input resistance Approx. 5.6k
OFF ON 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Response time
ON OFF 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Dielectric maximum voltage 560VAC rms/3 cycles (altitude 2000m) Insulation resistance 10M or more by insulation resistance tester
By noise simulator of 500Vp-p noise voltage, 1 s noise width and 25 to 60Hz noise frequency Noise immunity
First transient noise IEC61000-4-4: 1kV
Protection of degree IP2X
Common terminal arrangement 32 points/common (common terminal: 1B01, 1B02) Number of I/O occupied points 32 points (For I/O allocation on I/O mixed module, set 32 points.)
Operation indicator ON indication (LED), 32-point switchover using switch 2
External connections 40-pin connector
Applicable wire size 0.3mm2 (For A6CON1 or A6CON4) 3 External wiring connector A6CON1, A6CON2, A6CON3, A6CON4 (optional) Mixed connector/terminal block
conversion module A6TBXY36, A6TBXY54, A6TBX70 5VDC internal current consumption 130mA (TYP, all points ON)
Weight 0.20kg 1: For the setting method, refer to the Section 1.3.1.
2: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the latter half (Y00 to Y1F) LED indications.
3: When using A6CON2 or A6CON3, refer to Chapter 7.
4
MELSEC-Q
4 COMBINED I/O MODULE
External Connections Derating Chart
“à •” ‰ñ ˜H 1B20
1B01,1B02 24VDC
2B20
2B01,2B02
2A01,2A02 sw
L
1A05
2A05 L
12/24VDC LED
Internal circuit
Left side
(first half) Indication selector
circuit Right side
(latter half) 2
Internal circuit
Constant voltage circuit
90 80 70 60 50 100
400 10 20 30 40 5055 Ambient temperature
28.8VDC
(°C) (%)
ON Ratio
2: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the latter half (Y00 to Y1F) LED indications.
4
MELSEC-Q
4 COMBINED I/O MODULE
(2) Transistor Output Specification (Sink Type)
Type
Specifications QH42P I/O Module (Output Specification) Appearance Number of output points 32 points
Insulation method Photocoupler
Rated load voltage 12-24VDC (+20/-15%) Max. load current 0.1A/point, 2A/common Max. rush current 0.7A/10ms or less Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC (TYP.) 0.1A, 0.2VDC (MAX.) 0.1A
OFF ON 1ms or shorter
Response time
ON OFF 1ms or shorter (rated load, resistance load)
Surge killer Zener diode
Fuse None Voltage 12-24VDC (+20/-15%) (ripple ratio within 5%)
External power
supply Current 15mA /common (when 24VDC and all point is ON) Common terminal arrangement 32 points/common (common terminal: 2A01, 2A02)
Protection function
Provided (overheat protection function, overload protection function)
• Overheat protection function operate independently of each other.
• Overload protection function operate independently of each other.
QH42P
1B20 X00 1A20 X10 2B20 Y00 2A20 Y10 1B19 X01 1A19 X11 2B19 Y01 2A19 Y11 1B18 X02 1A18 X12 2B18 Y02 2A18 Y12 1B17 X03 1A17 X13 2B17 Y03 2A17 Y13 1B16 X04 1A16 X14 2B16 Y04 2A16 Y14 1B15 X05 1A15 X15 2B15 Y05 2A15 Y15 1B14 X06 1A14 X16 2B14 Y06 2A14 Y16 1B13 X07 1A13 X17 2B13 Y07 2A13 Y17 1B12 X08 1A12 X18 2B12 Y08 2A12 Y18 1B11 X09 1A11 X19 2B11 Y09 2A11 Y19 1B10 X0A 1A10 X1A 2B10 Y0A 2A10 Y1A 1B09 X0B 1A09 X1B 2B09 Y0B 2A09 Y1B 1B08 X0C 1A08 X1C 2B08 Y0C 2A08 Y1C 1B07 X0D 1A07 X1D 2B07 Y0D 2A07 Y1D 1B06 X0E 1A06 X1E 2B06 Y0E 2A06 Y1E 1B05 X0F 1A05 X1F 2B05 Y0F 2A05 Y1F 1B04 Vacant 1A04 Vacant 2B04 Vacant 2A04 Vacant 1B03 Vacant 1A03 Vacant 2B03 Vacant 2A03 Vacant 1B02 COM1 1A02 Vacant 2B02 12/24
VDC 2A02 COM2
Module front view
1B01 COM1 1A01 Vacant 2B01 12/24
VDC 2A01 COM2 4: Pin number of 1 indicates that of the left-hand side connector, and pin number of 2 indicates that of the right-hand
side connector.
MELSEC-Q
4 COMBINED I/O MODULE
4.2 QX41Y41P I/O Module
• When using the main module, use the constructions listed in Section 1.2.3 (2).
• This module uses sequential I/O numbers for input and output.
For I/O numbers of combined I/O modules, refer to Section 1.2.3.
(1) DC Input Specification (Positive Common Type)
Type
Specifications QX41Y41P I/O Module (Input Specification)
Number of input points 32 points
Insulation method Photocoupler
Rated input voltage 20.4 to 28.8VDC (ripple ratio within 5%)
Rated input current Approx. 4mA
Input derating See the derating chart.
ON voltage/ON current 19V or higher/3mA or higher OFF voltage/OFF current 11V or lower/1.7mA or lower
Input resistance Approx. 5.6k
OFF ON 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Response time
ON OFF 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Dielectric maximum voltage 560VAC rms/3 cycles (altitude 2000m) Insulation resistance 10M or more by insulation resistance tester
By noise simulator of 500Vp-p noise voltage, 1 s noise width and 25 to 60Hz noise frequency Noise immunity
First transient noise IEC61000-4-4: 1kV
Protection of degree IP2X
Common terminal arrangement 32 points/common (common terminal: 1B01, 1B02) Number of I/O occupied points 64 points (For I/O allocation on I/O mixed module, set 64 points.)
Operation indicator ON indication (LED), 32-point switchover using switch 2
External connections 40-pin connector
Applicable wire size 0.3mm2 (For A6CON1 or A6CON4) 3 External wiring connector A6CON1, A6CON2, A6CON3, A6CON4 (optional) Mixed connector/terminal block
conversion module A6TBXY36, A6TBXY54, A6TBX70 5VDC internal current consumption 130mA (TYP, all points ON)
Weight 0.20kg 1: For the setting method, refer to the Section 1.3.1.
2: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the latter half (Y00 to Y1F) LED indications.
3: When using A6CON2 or A6CON3, refer to Chapter 7.
MELSEC-Q
4 COMBINED I/O MODULE
External Connections Derating Chart
“à •” ‰ñ ˜H 1B20
1B01,1B02 24VDC
2B20
2B01,2B02
2A01,2A02 sw
L
1A05
2A05 L
12/24VDC LED
Internal circuit
Left side
(first half) Indication selector
circuit Right side
(latter half) 2
Internal circuit
Constant voltage circuit
90 80 70 60 50 100
400 10 20 30 40 5055 Ambient temperature
28.8VDC
(°C) (%)
ON Ratio
2: Selection of left-hand (F) side provides the first half (X00 to X1F) LED indications, and selection of right-hand (L) side provides the latter half (Y00 to Y1F) LED indications.
MELSEC-Q
4 COMBINED I/O MODULE
(2) Transistor Output Specification (Sink Type)
Type
Specifications QX41Y41P I/O Module (Output Specification) Appearance Number of output points 32 points
Insulation method Photocoupler
Rated load voltage 12-24VDC (+20/-15%) Max. load current 0.1A/point, 2A/common Max. rush current 0.7A/10ms or less Leakage current at OFF 0.1mA or lower
Max. voltage drop at ON 0.1VDC (TYP.) 0.1A, 0.2VDC (MAX.) 0.1A
OFF ON 1ms or shorter
Response time
ON OFF 1ms or shorter (rated load, resistance load)
Surge killer Zener diode
Fuse None Voltage 12-24VDC (+20/-15%) (ripple ratio within 5%)
External power
supply Current 15mA /common (when 24VDC and all point is ON) Common terminal arrangement 32 points/common (common terminal: 2A01, 2A02)
Protection function
Provided (overheat protection function, overload protection function)
• Overheat protection function operate independently of each other.
• Overload protection function operate independently of each other.
QX41Y41P
1B20 X00 1A20 X10 2B20 Y20 2A20 Y30 1B19 X01 1A19 X11 2B19 Y21 2A19 Y31 1B18 X02 1A18 X12 2B18 Y22 2A18 Y32 1B17 X03 1A17 X13 2B17 Y23 2A17 Y33 1B16 X04 1A16 X14 2B16 Y24 2A16 Y34 1B15 X05 1A15 X15 2B15 Y25 2A15 Y35 1B14 X06 1A14 X16 2B14 Y26 2A14 Y36 1B13 X07 1A13 X17 2B13 Y27 2A13 Y37 1B12 X08 1A12 X18 2B12 Y28 2A12 Y38 1B11 X09 1A11 X19 2B11 Y29 2A11 Y39 1B10 X0A 1A10 X1A 2B10 Y2A 2A10 Y3A 1B09 X0B 1A09 X1B 2B09 Y2B 2A09 Y3B 1B08 X0C 1A08 X1C 2B08 Y2C 2A08 Y3C 1B07 X0D 1A07 X1D 2B07 Y2D 2A07 Y3D 1B06 X0E 1A06 X1E 2B06 Y2E 2A06 Y3E 1B05 X0F 1A05 X1F 2B05 Y2F 2A05 Y3F 1B04 Vacant 1A04 Vacant 2B04 Vacant 2A04 Vacant 1B03 Vacant 1A03 Vacant 2B03 Vacant 2A03 Vacant 1B02 COM1 1A02 Vacant 2B02 12/24
VDC 2A02 COM2
Module front view
1B01 COM1 1A01 Vacant 2B01 12/24
VDC 2A01 COM2 4: Pin number of 1 indicates that of the left-hand side connector, and pin number of 2 indicates that of the right-hand
side connector.
MELSEC-Q
4 COMBINED I/O MODULE
4.3 QX48Y57 I/O Module
• When using the main module, use the constructions listed in Section 1.2.3 (2).
• This module uses sequential I/O numbers for input and output.
For I/O numbers of combined I/O modules, refer to Section 1.2.3.
(1) DC Input Specification (Positive Common Type)
Type
Specifications QX48Y57 I/O Module (Input Specification) Appearance
Number of input points 8 points
Insulation method Photocoupler
Rated input voltage 24VDC (+20/-15%, ripple ratio within 5%)
Rated input current Approx. 4mA
Input derating None
ON voltage/ON current 19V or higher/3mA or higher OFF voltage/OFF current 11V or lower/1.7mA or lower
Input resistance Approx. 5.6k
OFF ON 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Response time
ON OFF 1ms/5ms/10ms/20ms/70ms or less (CPU parameter setting) 1 Initial setting is 10ms
Dielectric maximum voltage 560VAC rms/3 cycles (altitude 2000m) Insulation resistance 10M or more by insulation resistance tester
By noise simulator of 500Vp-p noise voltage, 1 s noise width and 25 to 60Hz noise frequency Noise immunity
First transient noise IEC61000-4-4: 1kV
Protection of degree IP2X
Common terminal
arrangement 8 points/common (common terminal: TB9) Number of I/O occupied
points 16 points (For I/O allocation on I/O mixed module, set 16 points.) Operation indicator ON indication (LED)
External connections 18-point terminal block (M3 6 screw)
Applicable wire size Core cable: 0.3 to 0.75mm2 (Outside diameter: 2.8mm or smaller) Applicable connector terminal R1.25-3 (Terminals with sleeve cannot be used)
5VDC internal current
consumption 80mA (TYP, all points ON)
Weight 0.20kg
0