[PDF] Top 20 Fabrication and Characterization of (111)-Oriented and Nanotwinned Cu by Dc Electrodeposition
Has 10000 "Fabrication and Characterization of (111)-Oriented and Nanotwinned Cu by Dc Electrodeposition" found on our website. Below are the top 20 most common "Fabrication and Characterization of (111)-Oriented and Nanotwinned Cu by Dc Electrodeposition".
Fabrication and Characterization of (111)-Oriented and Nanotwinned Cu by Dc Electrodeposition
... layer and a 200 nm thick copper seed layer were sequentially sputtered on a silicon wafer by Oerlikon ClusterLine ...The Cu seed layer should have a (111) preferred ...Electroplating of the ... See full document
5
Correlation between the Microstructures of Bonding Interfaces and the Shear Strength of Cu-to-Cu Joints Using (111)-Oriented and Nanotwinned Cu
... analysis, and cowrote the paper. C.-L.L. contributed to sample fabrication and EBSD ...C.C., and K.N.T. led the Cu direct bonding project and co-wrote the ...Ministry of ... See full document
7
Effect of grain orientations of Cu seed layers on the growth of < 111 >-oriented nanotwinned Cu
... process, Cu seed layer plays a crucial role on the growth of the ...effect of seed layer orientations on the growth of ...deposition of nt-Cu films by pulsed ... See full document
4
Fabrication of (111)-Oriented Nanotwinned Au Films for Au-to-Au Direct Bonding
... methods of solder joints will cause a metallurgical interaction between solder balls, forming intermetallic compounds, voids and porous formation in Cu 3 Sn [2], and causing a brittle ... See full document
11
Microstructure control of unidirectional growth of eta-Cu6Sn5 in microbumps on < 1 1 1 > oriented and nanotwinned Cu
... single-crystal Cu. None of this earlier research has shown the orientation of Cu 6 Sn 5 after the surface morphol- ogy had ...growth of scallop-type Cu 6 Sn 5 continued even ... See full document
10
Fabrication and characterization of spherical polycrystalline diamond emitter arrays
... (100) oriented Si wafers having a resistivity of ...methanol, and DI-water and then dried with nitrogen gas. By using pyrogenic steam, the cleaned silicon wafer was thermally oxidized ... See full document
5
Fabrication and characterization of Schottky junctions of aluminum with polyaniline containing hydrolysis products
... Results and Discussion Preparation of PANI film with builtin hydrolysis ...products.— Electrodeposition of PANI was performed by cyclic voltammetry 共CV兲 at two different switching upper ... See full document
6
Fabrication and characterization of Cu-SiCp composites for electrical discharge machining applications
... Department of Materials Science and Engineering, National Chiao- Tung University 1001, Ta Hsueh Road, Hsinchu 30050, Taiwan ABSTRACT Cu–SiC p composites made by the powder metallurgy method ... See full document
22
Grain growth in electroplated (111)-oriented nanotwinned Cu
... bottom of the ...large nanotwinned grains A, B and C grew downward to consume the fine grains below them, and densely packed nanotwins also formed in the same ...slightly by FIB, ... See full document
4
Fabrication of porous nickel oxide film with open macropores by electrophoresis and electrodeposition for electrochemical capacitors
... Fabrication of porous nickel oxide film with open macropores by electrophoresis and electrodeposition for electrochemical capacitors Mao-Sung Wu ∗ , Min-Jyle Wang, Jiin-Jiang Jow ... See full document
3
Unidirectional Growth of Microbumps on (111)-Oriented and Nanotwinned Copper
... area by 4 orders of magnitude, yet the solder volume will be reduced by 6 orders of magni- ...point of the solder remains unchanged, meaning that each micro- bump may contain only a few ... See full document
5
Fabrication and characterization of biodegradable scaffold by electrospinning and its potential for cartilage tissue engineering
... aim of this thesis is development and investigation of cartilage tissue ...acid) and PBSA (Poly butylene succinate-co-adipate) with ...sacffold and TCPS (tissue culture ...PLLA ... See full document
1
Fabrication and Characterization of Benzocyclobutene Optical Waveguides by UV Pulsed-Laser Illumination
... fabricated by the UV pulsed-laser illumination method are proposed and comprehensively ...The fabrication method can not only simplify the fabrication process as re- quiring no further ... See full document
8
Fabrication and characterization of biodegradable scaffold by elec trospinning and its potential for cartilage tissue engineering
... Furthermore, we app lied the primary cell culture, seeded on PLLA PBSA sacffold and TCPS (ti ssue culture polystyrene).. We found that cells on the PLLA and PBSA scaf fold grew worse tha[r] ... See full document
2
Phase Transformation of Calcium Phosphates by Electrodeposition and Heat Treatment
... through water reduction, H 2 gas evolution at the interface leads to a heterogeneous coating. [13] Recent work has used organic solutions to avoid the negative effects of H 2 gas, and more homogeneous ... See full document
4
Fabrication and characterization of PZT thick films for sensing and actuation
... thicknesses of between 1 and 10 µm were successfully fabricated by the modified sol-gel method using two techniques - precursor concentration modulation and rapid thermal ...thickness ... See full document
15
Fabrication of various nickel nanostructures by manipulating the one-step electrodeposition process
... nickel electrodeposition process, the well- ordered colloidal crystal was not destroyed due to the presintering process performed at 135°C for 2 ...180 and 300 nm col- loidal diameter, respectively, which ... See full document
7
Characterization and fabrication of wireless flexible physiological monitor sensor
... design and fabrication process of a wireless flexible physiological monitor module, which is based on a polyimide substrate for a printed circuit and uses on a non-woven material to package ... See full document
4
Fabrication and characterization of micro-structured polymer optical fibers
... Abstract: Single-mode micro-stmctured polymer optical fibers over the wavelength range of 633 through 1550 nm are fabricated and characterized. The effects of drawing temperature and[r] ... See full document
2
Fabrication and Characterization of CMOS-MEMS Thermoelectric Micro Generators
... fabricated by the commercial ...process and the post-CMOS process. The micro generator is composed of 24 thermocouples in ...constructed by p-type and n-type polysilicon strips. The ... See full document
11
相關主題